Clean the pipe or bong

Robert Bergman, ILoveGrowingMarijuana.org

If you are someone who likes to smoke marijuana, which need necessarily to clean your pipe or bong at a particular time. The more you use favors smoking device , have to clean normally. In this article we will examine the best ways to do this.

Why is it necessary to clean the tube

As a container, to clean glass tube or pipe water is important because it affects smoke snuff. If you are using the device, you probably have been able to perfect the shot exactly to your liking, you can perfect smoke enter every time he did. But, probably has, over time, to change something started - probably often began obstacle, so it becomes increasingly difficult to meet. Here's how you know it's time to clean - and if not clean, then you will have trouble keeping, whenever you want to smoke.

Some people try just scratching the glass pipe or bong, when you get to this point, but unfortunately this is only a temporary solution - and a mediocre at best. Scraping can not get enough of resin, that means plugging it very soon.

cleaning Methods

Once you accept that it is time, in fact, you need to know how to clean a glass tube or a tube. Some people prefer a professional product to the store (or online) to buy and to use it for maximum speed and usability. Despite this reality, you need to get the remaining resin in its shell, but is also a very expensive way to do it. bought a bottle shop cleaner often has a starting price of around $ 20, which can be costly if you are a frequent user. That is, if this is the way you want to go, there are some good options here .

Fortunately, to purify homemade recipes, the tubes are simple and cheap, and ready to order just more work than just a bottle of detergent.

The process of salt and alcohol
For this process, the rubbing alcohol (requires isopropyl alcohol ) and brine.

To clean a hookah, pour a little alcohol and adding a lot of salt. Swish the mixture around until the resin or at least vaguely away, then rinse it all with a little hot and water regularly.

To clean a little more like a cup tube, you need alcohol, salt and a plastic bag. Pour rubbing alcohol and salt in the solution bag (or just do it separately, mixed in his pocket), then remove the hose into the bag. Seal and shake all content to on intensively for a while. If the hose is cured in an unusually thick layer of resin, it may be necessary to soak sitting with a solution of alcohol and salt in the bag overnight and sufficiently separate dissolve resin. Quit rinse through the glass tube with hot water. Inspect the hose to ensure that no resin remains; the process optionally repeated until no resin remains.

Some people prefer to try not to clean the resin, as easy to shake the bag and its contents. If you want to take this a little more active way, you can use wax loop or pipe cleaner (or both).

 

The process of boiling water and soap dish
First, fill a pot with warm water. Dip the glass tube in the water before the heat to a boil (otherwise causes the sudden change in temperature that the glass to break). the pot heated over medium heat (with water and the inner tube). Use pliers to inspect the glass tube - be filled with water, which does not allow air bubbles inside. Move for air bubbles if necessary.

Boil the water and the glass pipe sitting in the boiling water until the resin is the glass mostly off. Remove the pan from heat and let stand - to leave the glass tube in the water - for five to ten minutes. After waiting (waiting is crucial because sudden changes in the temperature of the glass may break), use pliers on the behavior of its trunk to hold and shake the entire interior of the water, which causes to break the resin and float tube. Be sure to hit the pipe on the sides of the pot, or damage that both.

Let allow water to cool completely, then pour into the drain and remove the hose. Put fresh water in the pot to add (at room temperature) and a small amount of detergent and the hose was found. Cotton swabs and pipe cleaners to clean with the pipe in the water until all the resin is lowered. Rinse with warm water.

cleaning Tips

Note that these cleaning methods are so clean especially for metal or glass. All other materials such as acrylic, should simply be soaked in warm water with a little detergent, then rubbed with a soft brush.

When a water pipe, which is longer than normal, can be filled with alcohol and rub saline and shake hands, the cover on both sides openings vigorously to dissolve the resin.

Download my growing marijuana free guide to this link for growing tips

Be sure to set the resin in the floor or carpet - is a nightmare to try it, if it is hooked to his belt.

If the glass tube cooking, one eye very close to it - cracks in the glass are not rare. For this reason, heat the water over medium heat (such as high temperature, in contrast).

Once your glass bong or pipe is completely clean, noticed the difference immediately. It will be like a new pipe brand, makes smoking more pleasant.

Thanks for reading. They let other proposals for the smoke machine cleaning - in the comments below - below, or if you want to know about the development of Bong, you will see in this article .

About Anthony Nelli

Anthony, co-founder and editor TheJointBlog, worked closely with officials many chosen to support the reform of the law on cannabis, including former campaign manager Washington State Representative Dave Upthegrove. It was also published by several media outlets, including The Seattle Times. It can be achieved TheJointBlog@TheJointBlog.com.

We block the advertising! (Why?)