professional management of the facility against the daily decisions on building maintenance costs, cleaning staff and operating. In this mixture of responsibilities is the implementation of a program of care on the ground that protects your investment in the floor and the bottom line. The most effective way to maintain the appearance of a finished floor is by adopting and following a program of regular maintenance and use of products that require less work.
shiny floors are literally a reflection of your business. It has been shown that the incidence of devices may likely decrease by 75 percent if the brightness of the system a bad first impression.
The following best practices and offers solutions to keep the shiny floors and contribute to a good first impression:
prevention
On average, one month working 22 days more than 26 pounds of dirt they can be tracked moves in a complex of 1,000 people through an inlet. By creating a program of the carpet in place, you can help to reduce the amount of dirt and soil moisture to enter into the building.
Mats must be located in high-traffic areas such as the main entrance, the entrance and the lobby inside and outside the building. In addition, mats throughout the building - continue to capture dirt penetration - near the stairs, the elevator shaft or other policy areas. Remember to clean carpets regularly.
And maintaining everyday
Your schedule and daily routine maintenance should include the following steps, depending on the installation and equipment. to get a clean ground on a regular basis is a simple way to achieve efficiency: it may allow you to delay indefinitely stripping and refinishing.
Dusting: always the most important elements of surface dirt begin to help clear a powder day. DUST bearing surface soil removal, so that is not integrated into the finish line, damaging the finish. Use oil as they can mop treatment based not leave a veil on the ground, which in turn attracts more dirt. For best results, make sure that the blade is clean from the start.
Wet cleaning: rake helps in removing moisture and oil debris. It also prevents the floor finish black or yellowing integrated country. Ensure a clean mop, you begin to use and follow the dilution ratio recommended by the manufacturer for cleaning floors with clean water. And be careful wipes too wet. You can leave the ground too wet cleaner to leave behind the ground, too. Finally, some products are recommended to rinse with clear water. Consider a cleaning product without flushing, which can improve efficiency by eliminating additional rinse step.
Car Scrubbing: This may not be possible for all systems, but the use of such devices can be more effective and more efficient. the better the wet mop the floor is removed and can use less chemicals. Do not forget the manufacturer and choose the right platform for cleaning dilution recommended to follow.
Low speed polishing: low speed finishing polishing helps to repair a soft glow and delay the need for housing. It's a good choice if your budget is not prohibited polisher. A relustrant durable finishes used to facilitate repair, maintainer sweep efficiency and select the appropriate pad for buffing. Remember, even clean the floors before polishing. Dirt integrate left on the floor with the cushion pad to the finish, if not cleaned first.
Honing with high speed: is much more effective high speed burnishing that polish at low speed, as these machines tend to be coarse speeds and pads. High-speed polishing also helps repair complete a soft glow and delays the need for a cover. If Browning likes to choose a floor, first, that your golden frequency matches, then select the appropriate polishing pad.
Important or frequency ground polished subject to the type of soil and the desired maintenance level. make a critical decision, choosing the right is quit adjust the desired level of maintenance and care the front. Each end is formulated with another spray pass and earnings.
between maintenance
If only the ground or polished helps lights down as desired, it may be time for an interim maintenance. This step involves deep cleaning and cover. It's easier to use a debugger to get a good deep clean and remove accumulated dirt, then follow with a rinse with clear water. Follow the manufacturer's instructions for the best results. After the peeling depth three applies to five thin layers of protective varnish for repainting. allow even thin, the formation of the surface, increased strength and durability. The frequency of Reapply depends on the amount of foot traffic and the amount of routine maintenance that is able to perform.
restoration care
Why strip and refinish? The soil tends to be darker and yellowed with time, despite the proper routine maintenance, it is important to regularly remove the old surface and apply a cool surface. Choose a cleaner product suitable floor finish and follow the manufacturer's instructions carefully, including the use of certain products and the waiting time.
Pointe High efficiency: Allow the product to do the job. After the waiting period suggested by the manufacturer, the best results. Stripper law should be received the full surface the first time, eliminating the need for a recovery areas eliminated a clean basis for rework. The productivity can maximize choose a rinse-free, low odor butyl separator be safely used in a plant, in particular 7.24 operates. After making sure the old paint is removed completely, it is time to apply the new surface.
critical decisions
Selecting the Best finish requires a comprehensive understanding of the needs of the characteristics of your company and product. First, note how routine maintenance, which can offer, including polishing or polishing. And then take into account the importance of the brightness levels of the country. For example, durable surfaces are often abrasions, scratches and wear and tear resistance. However, they have a lower browning reaction and can not have high brightness. blued finish, but they are designed for polishing. They may have higher levels of brightness, but offer need a little more care to keep this appearance.
It also allows the selection of suitable cleaning products for professional cleaning for best results. If inefficient cleaning products are used, the floor is left to create blunt or worn floor surfaces. The use of less efficient products have a negative impact on productivity, because employees need more clean and is more difficult to achieve the desired result. The smartest option is to use a neutral detergent, the effect is very effective in a variety of abrasive particles from the surface to remove soils. Proper law allows employees to easily reach more soil removal and help keep a bright and shiny appearance on the floor.
Facility managers should an end-end - maintenance such solution consider P & G Pro Line Floor Care - System lasting shine and helps the time between - the supply seamlessly long to work together are formulated cleaners, finishing and cleaning provides, the brush and the cover extend.
Floors and floor care maintenance are important investment for any business. Be sure to choose a floor care system that works together, there is a first impression to customers and visitors, and the life of the earth extends itself.
Joe Davis is an account executive focus at P & G Professional in the maintenance of floor cleaning and care.
Aucun commentaire:
Enregistrer un commentaire